LZ2822 Bottom Roller Bearing 16.5x28x19mm

H:473.075 mm; Housing:SAFS 052 KA; Cap bolt, SAE grade:8; J1:133.35 mm; J max.:708.025 mm; h:69.85 mm; Taconite seal:TER 553; A1:222.25 mm; Cap bolt recommended tightening torque:4284.4 N·m; PG:1/4 NPT;

D:150 mm; r2s (min):0.6 mm; a:33 mm; T:32 mm; rs (min):2 mm; C:24 mm; B:32 mm; r1s (min):1.5 mm; d2:100 mm; Dynamic (Ca):178 kN;

B:14.5 mm; d:150 mm; d1:212 mm; r1,2 min.:1.5 mm; Mass shaft washer:2.18 kg;

Basic Static Radial Load Rating Co:47500 N; Fillet Radius ra:1.50 mm; Sealed Speed Rating n3:4300 rpm; B:33.30 mm; D:100.0000 mm; Oil Speed Rating n2:5600 rpm; Accessories:No Shield, no Seal; d:55.000 mm; Grease Speed Rating n1:4300 rpm; Basic Dynamic Radial Load Rating C:57200 N;

Accessories:Two Seals & Snap-Rin; Basic Static Radial Load Rating Co:405000 N; Grease Speed Rating Open/Shielded n1:1400 rpm; d:280.000 mm; Oil Speed Rating Open/Shielded n2:1700 rpm; Sealed Speed Rating n3:890 rpm; D:420.0000 mm; Fillet Radius ra:3.00 mm; B:65.00 mm; Basic Dynamic Radial Load Ratin

Permissible sliding velocity v min.:0 m/s; Coefficient of friction µ max.:0.2; Coefficient of friction µ min.:0.02; L:500 mm; H:2.5 mm; Permissible sliding velocity v max.:2.5 m/s; B:100 mm; Mass strip:0.88 kg; Specific static load factor K0:250 N/mm²; Specific dynamic load factor K

Mass inner ring:0.033 kg; F:30 mm; B:20.5 mm; d:25 mm; r, r1,2 min.:0.3 mm;

B:35 mm; Mass inner ring:0.85 kg; F:145 mm; d:130 mm; r, r1,2 min.:1.1 mm;

Lock washer:W 40; B:30.429 mm; Hydraulic nut:HMVC 40E; Sleeve:S 140x7.3/16; B4:34.138 mm; B1:179.959 mm; Lock nut:AN 40; d:200 mm; d1:182.563 mm; d3 max.:250.165 mm;

Grease:2100 kN; B:75 mm; Dynamic (Cr):4.5 mm; rs (min):2.1 mm; with cylindrical bore:1 000 min-1; with tapered bore:1 400 min-1; Oil:179.000 kN; Pu:1000 kN; Static (Cor):8.3 mm; D:380 mm;

Grease Speed Rating n1:2200 rpm; Oil Speed Rating n2:3200 rpm; Basic Dynamic Radial Load Rating C:212000 N; B:50.00 mm; Fillet Radius ra:2.50 mm; Basic Static Radial Load Rating Co:228000 N; d:110.000 mm; D:240.0000 mm;

ra max.:2.5 mm; D:230 mm; Da max.:215.4 mm; D1 ≈:200.3 mm; C:40 mm; Calculation factor kr:0.15; Basic static load rating C0:305 kN; Fatigue load limit Pu:36.5 kN; Limiting value e:0.2; Axial load factor Y:0.6;

r1 max.:0.8 mm; Mass needle roller:2.15 g; r1,2 min.:0.3 mm; r2 max.:1 mm; Dw:4 mm; Lw:21.8 mm;

RG:1/8-27 NPT; DN:6.579 mm; Recommended tightening torque for grub screw:28.5 N·m; A1:19 mm; Recommended diameter for attachment bolts, inch G:0.75 in; Basic static load rating C0:49 kN; J:152.5 mm; d:74.613 mm; Thread grub screw G2:7/16-20 UNF; R1:41 mm;

Mass lock nut:2.6 kg; d1:222 mm; d3:240 mm; G:M 200x3; h:8 mm; Axial static load carrying capacity:625 kN; Lock washer / Locking clip:MBL 40; Associated spanner:TMFN 30-40; B:29 mm; b:18 mm;